Flowserve IPS-Beacon Bedienungsanleitung PDF herunterladen (Seite 6)

IPS BEACON ENGLISH 26999949 03-13

Page 6 of 16 flowserve.com

Table 1: IPS Beacon factory default settings

Parameter

Default setting

(metric units)

Default setting

(US units)

X-axis vibration

alarm level

9.4 mm/s

0.38 in./sec

Y-axis vibration

alarm level

9.4 mm/s

0.38 in./sec

Z-axis vibration

alarm level

9.4 mm/s

0.38 in./sec

Temperature

alarm level

85 °C

185 °F

Vibration

readings type

RMS

Data log interval

5 minutes

Average number

of readings for

alarm limit

2 readings

See section 5, Custom configuration programming, to

change any of the above settings.

3.2 Alarm mode

By default the IPS Beacon enters alarm mode when

the average of two readings, of either vibration or

temperature, exceed the predefined alarm limits.

Alarm mode is indicated with a flashing red light. The

user should do a physical detailed analysis of the

equipment being monitored when the alarm is

activated. (See Table 2: LED indicator lights

description with PUM installed.)

Table 2: LED indicator lights description with

PUM installed

LED

State

Description

GREEN

3 quick

flashes

Indicates that IPS Beacon has been

powered on

GREEN

Flash every

5 seconds

Normal operation – vibration and

temperature are within acceptable limits

RED

Flash every

5 seconds

Current alarm – one of the

measurements has exceeded its alarm

limit and has not returned within the

acceptable range

RED &

GREEN

Flash every

5 seconds

Alarm – one of the measurements

previously exceeded its alarm limit, but has

now returned within the acceptable range

3.3 Performance and operation limits

This product has been selected to meet the

specification of your purchase order.

The following data is included as additional

information to help with your installation. This is

typical information and if required, a definitive

statement for your application can be obtained from

Flowserve.

3.3.1 IPS Beacon nomenclature

Table 3: IPS Beacon nomenclature

Flowserve

item code

Generic

designation

Specifications

Material

9050

VB-105

IPS Beacon compact

monitor

316L SS

Fastener

M6 (¼ - 28)

18-8

This product must not be operated

beyond the parameters specified for the application.

If there is any doubt as to the suitability of the product

for the application intended, contact the manufacturer

for advice.

IPS Beacon material compatibility is

the responsibility of the end user.

3.3.2 Sensor specifications

Table 4: IPS Beacon and sensor specifications

IPS Beacon components

Channels (internal)

1-battery voltage, 1-onboard

temperature, 3-vibration (X, Y, Z)

Measurement rates

1 to 60 minutes

Ambient temperature

-40 °C (-40 °F) to +85 °C (185 °F)

Power requirement

3.6 VDC internal battery pack

Outer shell

316LSS with Borosilicate glass lens

Mounting

M6 (¼ x 28) stud mount

IPS Beacon sensor components

Variable

Limit

Vibration (velocity)

Tri axis 0-25 mm/s (0 – 1 IPS) peak or

RMS. Accuracy +/- 10 % full scale

Surface temperature (T

)

measurement range

-40 °C (-40 °F) ≤ T

≤ +93.33 °C (200

°F). Accuracy +/-2.8 °C (5 °F)

IPS Beacon

operational state

Battery life

Normal operating and

environmental conditions

4 years with 5 minute sampling

Alarm mode

4 years

Note: Measurement accuracy for surface temperature (range -40 to

93.33 °C) and vibration (range 0 to 25 mm/s) is absolute accuracy of

the measurement relative to a known, calibrated device. Values

shown represent the expected performance operating under steady

state conditions at 23 °C (73 °F) with no external interferences.

Note: The IPS Beacon temperature measurement is optimized for

surface temperature readings of an operating bearing housing.

3.3.3 Battery

The IPS Beacon battery is not

replaceable.

You must replace the entire unit once the battery runs

out of power. The battery life is not covered as part

of the standard device warranty. Table 4 shows the

average battery life under normal and alarm mode

operating conditions.

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Flowserve IPS-Beacon Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Flowserve IPS-Beacon