Flowserve ESP2 Bedienungsanleitung PDF herunterladen (Seite 9)

ESP2 USER INSTRUCTIONS ENGLISH PCN-(71569292) 4-12

Page 9 of 64

2 TRANSPORT AND STORAGE

2.1 Consignment receipt and unpacking

Immediately after receipt of the equipment it must be

checked against the delivery/shipping documents for

its completeness and that there has been no

damage in transportation. Any shortage and/or

damage must be reported immediately to Flowserve

Pump Division and must be received in writing within

ten days of receipt of the equipment. Later claims

cannot be accepted.

Check any crate, boxes or wrappings for any

accessories or spare parts that may be packed

separately with the equipment or attached to pallet,

box, or equipment.

Each product has a unique serial number. Check

that this number corresponds with the order. Always

quote this number in correspondence as well as

when ordering spare parts or further accessories.

2.2 Handling

Boxes, crates, pallets or cartons may be unloaded

using fork lift vehicles or slings dependent on their

size and construction. The unit should be stored in a

level position with no strains applied.

2.3 Lifting

Pumps and motors often have

integral lifting lugs or eye bolts. These are intended

for use in only lifting the individual piece of

equipment.

Do not use eye bolts or cast-in lifting

lugs to lift pump, motor and baseplate assemblies.

Care must be taken to lift components

or assemblies above the center of gravity to prevent

the unit from flipping. This is especially true with

In-Line pumps.

Carefully sling ESP pumps so that

bearing lubrication lines (3840.1) will not be bent or

damaged when lifting.

It is advisable to raise the pump into the vertical

position before uncrating. If this isn't possible, pumps

over eight feet long must be supported at more than

one place when raising to the vertical position. Use a

support strap around the bottom column (1341.2)

and on the motor support (3160).

Pump Weights

ESP2

Base Pump

Kg (lb) per 0.15m

(6 in.)

Pump Size

Wt. Kg (lb)

Extra Length

Group 1

1.5x1x6

136 (300)

3.6 (8)

3x1.5x6

139 (305)

3.6 (8)

3x2x6K

145 (320)

4.1 (9)

1.5x1x8

148 (325)

3.6 (8)

3x1.5x8

150 (330)

3.6 (8)

3x2x8

152 (335)

4.1 (9)

Group 2

3x1.5x8

182 (400)

6.8 (15)

3x2x8

184 (405)

7.3 (16)

4x3x8

223 (490)

7.7 (17)

4x3x8L

223 (490)

7.7 (17)

2x1x10

182 (400)

6.8 (15)

3x1.5x10

223 (490)

6.8 (15)

3x2x10

232 (510)

7.3 (16)

4x3x10

286 (630)

7.7 (17)

4x3x10L

309 (680)

7.7 (17)

6x4x10

323 (710)

8.6 (19)

3x1.5x13

259 (570)

6.8 (15)

3x2x13

264 (580)

7.3 (16)

4x3x13

302 (665)

7.7 (17)

Group 3

6x4x13

407 (895)

11.4 (25)

8x6x13

545 (1200)

15 (33)

10x8x13 616 (1355)

16.4 (36)

8x6x15

561 (1235)

15 (33)

10x8x15

645 (1420)

16.4 (36)

Base pump lengths are 0.61m (2 ft.) for

Group 1 & Group 2 pumps and 0.91m (3 ft.) for Group

3 pumps.

On pumps equipped with grease lubricated

shaft bearings, (3020.1 and 3020.2) take care not to

flush the grease from the bearings.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 61 62

Kommentare zu diesen Handbüchern

Keine Kommentare

Flowserve ESP2 Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Flowserve ESP2